Is Overgreasing Dangerous?

 Greasing is an important process that ensures the smooth functioning of machines. Let’s understand these two aspects first - Overgreasing and Undergreasing. To determine which of these is more problematic could be difficult but we can definitely decide which one is more damaging. Too much grease can generate excessive heat in the bearing and may result in seal failure. When the lip seals rupture because of over greasing, it allows the harmful contaminants to enter the bearing housing. This would create excessive pressure and may collapse the bearing race. On the other hand, not putting enough grease may cause damage to the rotating parts. Undergreasing allows contaminants to enter the load zones. We can say that it's better to avoid both aspects of over and under greasing.

How to determine the amount of grease a bearing needs?

The factor responsible for determining the right amount of grease depends on the dimensions of the bearing or its housing. Greasing must be done based on proper calculations. A formula that is used commonly is as follows:

The outside diameter of the bearing is multiplied by the width (in inches), then multiply the answer by 0.114. This would give you the amount of grease in ounces required for that particular bearing.

For example -

If the outside diameter of a bearing is 3 inches and the width of a bearing is 0.5 inches, then

3 X 0.5 = 1.5

1.5 X 0.114 = 0.17

Thus, The amount of grease needed is 0.17 ounces or 4.8 grams.

Still not sure how? Connect with our experts: Click Here

How to solve the problem of Overgreasing?

After having a grip on how much grease to put, try to master the frequency. Take help from various tables and charts available for determining the frequency. Calibrating the grease guns could be a simple and easy step to determine the correct volume of grease. It is very important to discontinue greasing when any abnormal pressure is encountered. Manual grease guns used in the industry have a few disadvantages. The poor control of grease guns may lead to over/under lubrication. Because they are low in cost, easy to use, and allow the technicians to inspect the equipment during the tasks, industries prefer using manual grease guns.

Setting up a maintenance program could be a game-changer. Keep a track of each grease point and schedule maintenance & inspections for the same. Initially, it may take some time and effort but the end result would be great and impactful.

Follow Minimac Systems to never miss updates on our upcoming webinars and technical articles!!


Comments

Post a Comment

Popular posts from this blog

Control System Of Turbine - Failure & Maintenance

Image
Control System The turbine control system describes the control over the opening of control valves corresponding to demand signals, and steam flows into the turbine with the help of a governing system that facilitates the operation of the turbo set in an interconnected grid system. Governing system is responsible for various function such as speed & load control functions, the start-up/shut-down controls, the over-speed control, turbine stress calculation, to control the initial run-up and synchronization of the Unit, to assists in matching the power generated to that demanded by responding to system frequency changes, to regulate the steam control valves position (and hence the load generated)in response to signal from the operator or from the load dispatch Centre, to restrict the speed rise within acceptable limits should the unit get disconnected (islanding) from the lgridoad and some protective trip functions. With continuous research and developments in modern turbine technolo
Read more

Minimac Technology

Image
 The secret recipe of the growth story at Minimac Syste ms has been its capability to drive technological advancement in the field of contamination control for lubrication reliability. Research and development on technology and products have always been the key reason to keep the Minimac products a step ahead of its competitors in the market. Technological development has been one of the core competencies which Minimac possesses, thereby ensuring a definite competitive advantage. Contaminations in lubricants are of various types and characteristics depending on the lubricant, equipment application, ambient conditions, age of equipment, etc. In order to control, separate or eliminate the contamination, there are multiple techniques. Each technique has pros and cons and hence there is no single technology that can be considered universally better than others. ​ Minimac Systems over the years has become equipped with almost all the technologies which are required for contaminat
Read more

Storage Management of Oil Products and its Importance.

Image
Product storage is an important criterion for any segment of products. It plays a vital role in the longevity of the products, every product in any form has a certain life period and this life period forms the baseline of the product. Coming to the lubricating oil industry, product life period plays an important role in the smooth running of the machinery and the plant. As these oils play a very important role in the day to day functioning of critical machinery, so if not maintained properly these can lead to the breakdown of machinery thereby leading to a shutdown of the plant which leads to the incurrence of huge loss. Therefore it is very important that these oils should be used well in advance before their life period expires. We can hereby pen down certain prerequisite conditions for storage of lubricants: 1.  Pre usage Inspection : It is mandatory to verify their performance properties & conditions with oil analysis for the oils that have been kept for a long pe
Read more