Are you experiencing sub-optimal results even after changing filters?

We have talked about how to procure filters and what specifications to look for, but selecting the filter according to the specifications doesn’t ensure the best results if a filter is not employed properly. In this article, we will discuss a few factors which can impair a filter's performance.
I hope you have read these 2 articles: 1.http://bit.ly/35J0Vuy 2.http://bit.ly/2QInSKiWhenever you are experiencing sub-optimal results even after changing filters, below are some possibilities which should be checked for :
 1. Collapsed center tube
2. Inconsistent media quality
3. Damaged or burst filter media – fatigue
4. Bypass at filter media seam
5. Bypass due to adhesive failure
6. Damaged gasket or O-ring seal
7. Bypass valve jammed in open/closed position
8. Installation error, installing a filter in the opposite flow direction
9. Bypass valve leakage
10. Misaligned filter and seal
If none of the above factors contribute to the sub-optimal functioning of your filters we suggest you contact the Minimac Consulting team for required filter calculations and further investigations.
Get your filter check today, Call +91 7030901266We at Minimac Systems Pvt Ltd. provide services of Total Lubrication Management and Lubrication Consulting that helps you optimize your Lubrication needs. Minimac stands for MINImum MAChinery Maintenance.
Source: www.noria.com

Comments

Post a Comment

Popular posts from this blog

Control System Of Turbine - Failure & Maintenance

Image
Control System The turbine control system describes the control over the opening of control valves corresponding to demand signals, and steam flows into the turbine with the help of a governing system that facilitates the operation of the turbo set in an interconnected grid system. Governing system is responsible for various function such as speed & load control functions, the start-up/shut-down controls, the over-speed control, turbine stress calculation, to control the initial run-up and synchronization of the Unit, to assists in matching the power generated to that demanded by responding to system frequency changes, to regulate the steam control valves position (and hence the load generated)in response to signal from the operator or from the load dispatch Centre, to restrict the speed rise within acceptable limits should the unit get disconnected (islanding) from the lgridoad and some protective trip functions. With continuous research and developments in modern turbine technolo
Read more

Reconditioning of EH Oil

Image
A 1200 MW coal-fired thermal power plant using Into-Chinese Turbine EHC System in Southern India. The Plant was struggling with the rapid increase in TAN values in the EH oil of the governing system of the turbine. Also, the moisture content was more than permissible limits. Degradation of the oil was due to contamination ingression into the system resulting in by-product formation. Minimac’s EH oil reconditioning system “ MLC LVDH TRIX 20 ” proved to be the savior and an unexpected shutdown of the turbine worth ₹1.05 Cr per day was saved . PROBLEMS A rapid increase in the Total Acid Number (TAN) could degrade the EH oil and lead to the possibilities of failure of servo valve, hunting, power generation loss, unplanned shutdown, etc. Oil Analysis was done to check the properties of EH oil like Moisture, NAS value, Total Acid Number. SOLUTIONS Installation of Minimac’s EH Oil Reconditioning System “ MLC LVDH TRIX 20 ” is comprehensively designed with 4 major technologies to: Remove solid
Read more

Minimac Technology

Image
 The secret recipe of the growth story at Minimac Syste ms has been its capability to drive technological advancement in the field of contamination control for lubrication reliability. Research and development on technology and products have always been the key reason to keep the Minimac products a step ahead of its competitors in the market. Technological development has been one of the core competencies which Minimac possesses, thereby ensuring a definite competitive advantage. Contaminations in lubricants are of various types and characteristics depending on the lubricant, equipment application, ambient conditions, age of equipment, etc. In order to control, separate or eliminate the contamination, there are multiple techniques. Each technique has pros and cons and hence there is no single technology that can be considered universally better than others. ​ Minimac Systems over the years has become equipped with almost all the technologies which are required for contaminat
Read more