Common mistakes of Oil Sampling and how to avoid them?

 

Routine Oil sampling and analysis are crucial for a successful maintenance program. It provides important information to determine the condition of the equipment. Sampling is a vital procedure for collecting fluid from machinery for the purpose of oil analysis. The results and reports of oil analysis depend on the quality of the oil sample.
Thus, oil sampling must be performed keeping some important goals in mind -

  • To MAXIMIZE the Data Density.
  • To MAXIMIZE Consistency.
  • To MAXIMIZE Relevance.
  • To MINIMIZE Data Disturbance.

There can be three ways of extracting samples from a component - drain port, drop-tube (in a vacuum pump), and a dedicated sampling point. A common mistake is taking an oil sample from the reservoir in circulating and hydraulic systems. Taking samples from the tank is not a best practice. If the sample is taken from the drain lines before emptying the tank, the concentration of wear metal would be much higher.
Let’s discuss the common mistakes of oil sampling which can be avoided -

  1. Some sampling methods are simply used for convenience, like inadequate flushing, using a vacuum pump (drop-tube sampling), usage of uncleaned bottles, etc. By following these bad practices, the quality of the sample taken is not apt and reliable.
  2. If the samples are collected from the bottom of the tank and sumps, they may show higher concentrations of the sediments and water.
  3. If the samples are consistently collected from the turbulent zones of reservoirs and tanks may not give reliable information.
  4. Sometimes the sample is collected consistently from downstream of pressure-line or off-line. In this case, sampling accuracy is not given importance.
  5. Samples collected from cold systems would not give correct information as the contaminants and other insoluble suspended particles would be settled when at rest.
  6. Dead zone fluids like standpipe, regenerative loops, etc. give wrong results as they possess different properties than that working fluids.

Subscribe to our website blog for more technical articles and case studies: Click here

The International Organization for Standardization (ISO) has some defined codes which are mostly used as the primary reviewed piece of data. Being consistent is important with sampling. It is not advisable to use different sampling methods. Let’s discuss certain must-follow sampling rules for oil analysis -

  1. Collect samples from running machines not from cold machines or stand-by machines. It is always advisable to start the machine and take the sample and the time of sample should be when the machine is at its peak of stress.
  2. What, when, who, where, and how should be defined for oil sampling procedures as well, just like maintenance procedures are defined in detail. Changing the sampling methods or location is not advisable.
  3. Use a specific sample point based on the type of lubricant, pressure, and the fluid required.
  4. A sample must be taken in a bottle of the correct size and cleanliness. To get more information on bottle cleanliness, ISO 3722 can be referred to.
  5. Oil sampling is like examining the condition of the system for that point in time. It is advisable not to wait for more than 24 hours to send the samples for oil analysis. This is because the health of the system may change in a very short period. Early detection would help in early remedy.
  6. Maintain proper frequency of taking samples. Don’t do it whenever you feel like doing it. There should be an appropriate frequency so that important maintenance decisions could be taken on time.
  7. One of the major problems in oil sampling is cross-contamination. Don’t use dirty sampling equipment. Flushing is the solution to this which is often overlooked and the selection of suitable clear media is equally important.

Though every system has a unique consideration of sampling, the above-mentioned tips can be applied and taken care of for your sampling techniques/methods. Start applying it Today!!

Connect with Minimac Experts to strategize your Oil Analysis plan: enquiry@minimac.in or WhatsApp us at +91 70309 01267

Comments

Post a Comment

Popular posts from this blog

Control System Of Turbine - Failure & Maintenance

Image
Control System The turbine control system describes the control over the opening of control valves corresponding to demand signals, and steam flows into the turbine with the help of a governing system that facilitates the operation of the turbo set in an interconnected grid system. Governing system is responsible for various function such as speed & load control functions, the start-up/shut-down controls, the over-speed control, turbine stress calculation, to control the initial run-up and synchronization of the Unit, to assists in matching the power generated to that demanded by responding to system frequency changes, to regulate the steam control valves position (and hence the load generated)in response to signal from the operator or from the load dispatch Centre, to restrict the speed rise within acceptable limits should the unit get disconnected (islanding) from the lgridoad and some protective trip functions. With continuous research and developments in modern turbine technolo
Read more

Minimac Technology

Image
 The secret recipe of the growth story at Minimac Syste ms has been its capability to drive technological advancement in the field of contamination control for lubrication reliability. Research and development on technology and products have always been the key reason to keep the Minimac products a step ahead of its competitors in the market. Technological development has been one of the core competencies which Minimac possesses, thereby ensuring a definite competitive advantage. Contaminations in lubricants are of various types and characteristics depending on the lubricant, equipment application, ambient conditions, age of equipment, etc. In order to control, separate or eliminate the contamination, there are multiple techniques. Each technique has pros and cons and hence there is no single technology that can be considered universally better than others. ​ Minimac Systems over the years has become equipped with almost all the technologies which are required for contaminat
Read more

Storage Management of Oil Products and its Importance.

Image
Product storage is an important criterion for any segment of products. It plays a vital role in the longevity of the products, every product in any form has a certain life period and this life period forms the baseline of the product. Coming to the lubricating oil industry, product life period plays an important role in the smooth running of the machinery and the plant. As these oils play a very important role in the day to day functioning of critical machinery, so if not maintained properly these can lead to the breakdown of machinery thereby leading to a shutdown of the plant which leads to the incurrence of huge loss. Therefore it is very important that these oils should be used well in advance before their life period expires. We can hereby pen down certain prerequisite conditions for storage of lubricants: 1.  Pre usage Inspection : It is mandatory to verify their performance properties & conditions with oil analysis for the oils that have been kept for a long pe
Read more